Product Line

Carbon Series Resistors

Product Name : ZERO-OHM & JUMPER WIRE

Item No. : ZR & JP

Description


ZERO-OHM:
ZERO OHM RESISTOR:


DIMENSIONS:


Construction Part Number L D H (Min) d
ceramic (Metal Body) ZR 12*-OR-C(M) 3.8±0.5 1.8±0.2 27 0.45±0.05
ceramic (Metal Body) ZR 25*-OR-C(M) 6.5±0.3 2.5±0.2 27 0.6±0.05
ceramic (Metal Body) ZR- 50-OR-C(M) 9±0.5 3.2 25 0.6±0.05
ceramic (Metal Body) ZR- 100-OR-C(M) 11 4.5 30 0.8±0.03
ceramic (Metal Body) ZR- 200-OR-C(M) 16 6 30 0.8±0.03


JUMPER WIRE:
Tape TYPE: M-Form:

DIMENSIONS:
TYPE DIMENSION (mm)
W±1 L±1 d±0.02 -0.05 H P
JW05 52 26 61.5 0.5 5~10 2.5~40
JW06 52 26 61.5 0.6 5~10 2.5~40
JW07 52 26 61.5 0.7 5~10 2.5~40
JW08 52 26 61.5 0.8 5~10 2.5~40
JW1.0 52 26 61.5 1.0 8~10 2.5~40
JW1.2 52 26 61.5 1.2 8~10 2.5~40

TEST TEST METHOD LIMITS
RESISTANCE ..........<0.005 ohm
OPERATING TEMPERATURE ..........-55℃ to +155℃
MAX. CURRENT ..........5.amps
MAX. WORKING VOLTAGE ..........300Vdc
MAX. OVERLOAD VOLTAGE ..........600Vdc
TEMPERATURE COEFFICIENT ....(PPM/ ℃) to - 100PPM
SHORT TIME OVERLOAD ....Apply 2.5 times the voltage rating for 5 sec.......................................... NO VISIBLE DAMAGE
LOAD LIFE ....1,000 hrs. at 70℃ a direct voltage applied cycles of 1.5 hrs. on and 0.5hrs. off throughout test................... △R=0.5%
TEMPERATURE CYCLING ....5 cycles of 30 min. duration at the extremes of temp range. maximum and minimum, measurement of ohmic value 4 hrs. after completion of test..... △R=0.5%
DIELECTRIC STRENGTH ....Using a 90° 〝V〞shaped conductive block apply 100V minimum, Increasing 100V sec. for 5 sec. .......................... △R=0.5%
HUMIDITY ....350 hrs. at 40° , 90 TO 95%Rh.... △R=0.5%
SOLDERABILITY ....Dipped in Sn/Pb (60/40) at 235° ,5sec. 1.5mm from the body...... 95% of TESTED SURFACE COVERED
VIBRATION ....By MIL STD.202,201A
TEMINAL ROBUSTNESS ....Traction, applied 2.5kg. for 10 sec. Bends, 2bends 90℃ applying load to terminals of 0.5kg. Twist, 2 successive turns 180° ,6mm from body............... NO VISIBLE DAMAGE
RESISTANCE TO SOLVENTS ....Trichlorethylene, TMC as the most aggressives for 60 sec. at boiling point. NO VISIBLE DAMAGE

APPLICATIONS:
  • Molded jumper wires of crossovers, as they are sometimes called, are basically interconnection devices between points on a PC board.
  • Generally they are used for the following reasons:
  • Inability to connect two points on a PC board due to other circuit paths which must be crossed over.
  • An after-the- fact design change that requires new point connections.
  • Circuit tuning by changing point connections.
  • Optional feature applications.


Loading...